View MCP1402T-EOT_2520123.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2007 microchip technology inc. ds22052a-page 1 mcp1401/02 features ? high peak output current: 500 ma (typ.) ? wide input supply voltage operating range: - 4.5v to 18v ? low shoot-through/cross-conduction current in output stage ? high capacitive load drive capability: - 470 pf in 19 ns (typ.) - 1000 pf in 34 ns (typ.) ? short delay times: 35 ns (typ.) ? matched rise/fall times ? low supply current: - with logic ? 1 ? input ? 850 ma (typ.) - with logic ? 0 ? input ? 100 ma (typ.) ? latch-up protected: will withstand 500 ma reverse current ? logic input will withstand negative swing up to 5v ? space-saving 5l sot-23 package applications ? switch mode power supplies ? pulse transformer drive ? line drivers ? motor and solenoid drive general description the mcp1401/02 are high speed mosfet drivers capable of providing 500 ma of peak current. the inverting or non-inverting single channel output is directly controlled from ei ther ttl or cmos (3v to 18v). these devices also feature low shoot-through current, matched rise/fall times and propagation delays which make them ideal for high switching frequency applications. the mcp1401/02 devices operate from a 4.5v to 18v single power supply and can easily charge and dis- charge 470 pf gate capacitance in under 19 ns (typ). they provide low enough impedances in both the on and off states to ensure the mosfets intended state will not be affected, even by large transients. these devices are highly latch-up resistant under any conditions within their power and voltage ratings. they are not subject to damage when up to 5v of noise spiking (of either polarity) occurs on the ground pin. they can accept, without damage or logic upset, up to 500 ma of reverse current being forced back into their outputs. all terminals are fully protect against electro- static discharge (esd) up to 3 kv (hbm) and 400v (mm). package types 4 1 2 3 5 v dd gnd in out gnd out gnd mcp1401 mcp1402 sot-23-5 tiny 500 ma, high-speed power mosfet driver
mcp1401/02 ds22052a-page 2 ? 2007 microchip technology inc. functional block diagram effective input c = 25 pf mcp1401 inverting mcp1402 non-inverting input gnd v dd 300 mv 4.7v inverting non-inverting 850 a output (each input)
? 2007 microchip technology inc. ds22052a-page 3 mcp1401/02 1.0 electrical characteristics absolute maximum ratings ? supply voltage ................................................................+20v input voltage ............................... (v dd + 0.3v) to (gnd ? 5v) input current (v in >v dd )................................................50 ma package power dissipation (t a = 50 o c) 5l sot23 ..................................................................0.39w ? notice: stresses above those listed under "maximum ratings" may cause permanent dam age to the device. this is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational sections of this specification is not intended. exposure to maximum rating conditions for extended periods may affect device reliability. dc characteristics (note 2) electrical specifications: unless otherwise indicated, t a = +25c, with 4.5v v dd 18v. parameters sym min typ max units conditions input logic ? 1 ?, high input voltage v ih 2.4 1.5 ? v logic ? 0 ?, low input voltage v il ?1.30.8v input current i in ?1 ? 1 a 0v v in v dd input voltage v in -5 ? v dd +0.3 v output high output voltage v oh v dd ? 0.025 ? ? v dc test low output voltage v ol ? ? 0.025 v dc test output resistance, high r oh ?1218 i out = 10 ma, v dd = 18v output resistance, low r ol ?1016 i out = 10 ma, v dd = 18v peak output current i pk ?0.5?av dd = 18v (note 2) latch-up protection with- stand reverse current i rev ? >0.5 ? a duty cycle 2%, t 300 s switching time (note 1) rise time t r ?1925ns figure 4-1 , figure 4-2 c l = 470 pf fall time t f ?1520ns figure 4-1 , figure 4-2 c l = 470 pf delay time t d1 ?3540ns figure 4-1 , figure 4-2 delay time t d2 ?3540ns figure 4-1 , figure 4-2 power supply supply voltage v dd 4.5 ? 18.0 v power supply current i s ? 0.85 1.1 ma v in = 3v i s ? 0.10 0.20 ma v in = 0v note 1: switching times ensured by design. 2: tested during characterization, not production tested.
mcp1401/02 ds22052a-page 4 ? 2007 microchip technology inc. dc characteristics (over ope rating temperature range) temperature characteristics electrical specifications: unless otherwise indicated, operat ing temperature range with 4.5v v dd 18v. parameters sym min typ max units conditions input logic ? 1 ?, high input voltage v ih 2.4 ? ? v logic ? 0 ?, low input voltage v il ??0.8v input current i in ?10 ? +10 a 0v v in v dd input voltage v in -5 ? v dd +0.3 v output high output voltage v oh v dd ? 0.025 ? ? v dc test low output voltage v ol ? ? 0.025 v dc test output resistance, high r oh ?1218 i out = 10 ma, v dd = 18v output resistance, low r ol ?1016 i out = 10 ma, v dd = 18v switching time (note 1) rise time t r ?2030ns figure 4-1 , figure 4-2 c l = 470 pf fall time t f ?1828ns figure 4-1 , figure 4-2 c l = 470 pf delay time t d1 ?4051ns figure 4-1 , figure 4-2 delay time t d2 ?4051ns figure 4-1 , figure 4-2 power supply supply voltage v dd 4.5 ? 18.0 v power supply current i s ? ? 0.90 0.11 1.10 0.20 ma ma v in = 3v v in = 0v note 1: switching times ensured by design. 2: tested during characterization, not production tested. electrical specifications: unless otherwise noted, all parameters apply with 4.5v v dd 18v. parameters sym min typ max units conditions temperature ranges specified temperature range t a ?40 ? +125 c maximum junction temperature t j ? ? +150 c storage temperature range t a ?65 ? +150 c package thermal resistances thermal resistance, 5l-sot23 ja ?256 ?c/w
? 2007 microchip technology inc. ds22052a-page 5 mcp1401/02 2.0 typical performance curves note: unless otherwise indicated, t a = +25c with 4.5v v dd 18v. figure 2-1: rise time vs. supply voltage. figure 2-2: rise time vs. capacitive load. figure 2-3: rise and fall times vs. temperature. figure 2-4: fall time vs. supply voltage. figure 2-5: fall time vs. capacitive load. figure 2-6: propagation delay vs. input amplitude. note: the graphs and tables provided following this note ar e a statistical summary based on a limited number of samples and are provided for informational purposes only. the performance characteristics listed herein are not tested or guaranteed. in some graphs or t ables, the data presented ma y be outside the specified operating range (e.g., outside specified power suppl y range) and therefore outs ide the warranted range. 0 50 100 150 200 250 300 350 4 6 8 1012141618 supply voltage (v) rise time (ns) 3300 pf 470 pf 100 pf 1000 pf 0 50 100 150 200 250 100 1000 10000 capacitive load (pf) rise time (ns) 5v 18v 12v 10 14 18 22 26 30 34 -40 -25 -10 5 20 35 50 65 80 95 110 125 temperature ( o c) time (ns) c load = 470 pf v dd = 12v t fall t rise 0 50 100 150 200 250 300 350 4 6 8 1012141618 supply voltage (v) fall time (ns) 3300 pf 470 pf 100 pf 1000 pf 0 50 100 150 200 250 100 1000 10000 capacitve load (pf) fall time (ns) 5v 18v 12v 36 37 38 39 40 41 42 43 44 45678910 input amplitude (v) propagation delay (ns) t d2 t d1 v dd = 12v
mcp1401/02 ds22052a-page 6 ? 2007 microchip technology inc. typical performance curves (continued) note: unless otherwise indicated, t a = +25c with 4.5v v dd 18v. figure 2-7: propagation delay time vs. supply voltage. figure 2-8: propagation delay time vs. temperature. figure 2-9: quiescent current vs. supply voltage. figure 2-10: quiescent current vs. temperature. figure 2-11: input threshold vs. supply voltage. figure 2-12: input threshold vs. temperature. 30 40 50 60 70 80 4 6 8 1012141618 supply voltage (v) propagation delay (ns) t d2 t d1 30 35 40 45 50 55 60 -40 -25 -10 5 20 35 50 65 80 95 110 125 temperature ( o c) propagation delay (ns) v dd = 12v t d2 t d1 0.0 0.2 0.4 0.6 0.8 1.0 1.2 4 6 8 1012141618 supply voltage (v) quiescent current (ma) input = 1 input = 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 -40 -25 -10 5 20 35 50 65 80 95 110 125 temperature ( o c) quiescent current (ma) v dd = 18v input = 1 input = 0 1.5 1.6 1.7 1.8 1.9 2 2.1 2.2 4 6 8 10 12 14 16 18 supply voltage (v) input threshold (v) v lo v hi 1.6 1.7 1.8 1.9 2 2.1 2.2 2.3 2.4 -40 -25 -10 5 20 35 50 65 80 95 110 125 temperature ( o c) input threshold (v) v dd = 12v v lo v hi
? 2007 microchip technology inc. ds22052a-page 7 mcp1401/02 typical performance curves (continued) note: unless otherwise indicated, t a = +25c with 4.5v v dd 18v. figure 2-13: supply current vs. capacitive load. figure 2-14: supply current vs. capacitive load. figure 2-15: supply current vs. capacitive load. figure 2-16: supply current vs. frequency. figure 2-17: supply current vs. frequency. figure 2-18: supply current vs. frequency. 0 25 50 75 100 125 150 100 1000 10000 capacitive load (pf) supply current (ma) 100 khz v dd = 18v 2 mhz 1 mhz 200 khz 50 khz 0 10 20 30 40 50 60 70 100 1000 10000 capacitive load (pf) supply current (ma) 100 khz v dd = 12v 2 mhz 1 mhz 200 khz 50 khz 0 5 10 15 20 25 30 100 1000 10000 capacitive load (pf) supply current (ma) 100 khz v dd = 6v 2 mhz 1 mhz 200 khz 50 khz 0 10 20 30 40 50 60 70 80 10 100 1000 frequency (khz) supply current (ma) v dd = 18v 6,800 pf 3,300 pf 1,000 pf 470 pf 100 pf 0 10 20 30 40 50 10 100 1000 frequency (khz) supply voltage (v) v dd = 12v 6,800 pf 3,300 pf 1,000 pf 470 pf 100 pf 0 5 10 15 20 25 10 100 1000 frequency (khz) supply current (ma) v dd = 6v 6,800 pf 3,300 pf 1,000 pf 470 pf 100 pf
mcp1401/02 ds22052a-page 8 ? 2007 microchip technology inc. typical performance curves (continued) note: unless otherwise indicated, t a = +25c with 4.5v v dd 18v. figure 2-19: output resistance (output high) vs. supply voltage. figure 2-20: output resistance (output low) vs. supply voltage figure 2-21: crossover energy vs. supply voltage 0 10 20 30 40 50 60 4 6 8 1012141618 supply voltage (v) r out-hi (m ? ) v in = 0v (mcp1401) v in = 5v (mcp1402) t j = +125 o c t j = +25 o c 5 10 15 20 25 30 35 40 45 50 4 6 8 1012141618 supply voltage (v) r out-lo (m ? ) v in = 5v (mcp1401) v in = 0v (mcp1402) t j = +125 o c t j = +25 o c 1e-10 1e-9 1e-8 1e-7 4 6 8 1012141618 supply voltage (v) crossover energy (a*sec)
? 2007 microchip technology inc. ds22052a-page 9 mcp1401/02 3.0 pin descriptions the descriptions of the pins are listed in table 3-1 . table 3-1: pin function table (1) 3.1 supply input (v dd ) v dd is the bias supply input for the mosfet driver and has a voltage range of 4.5v to 18v. this input must be decoupled to ground with a local capacitor. this bypass capacitor provides a localized low-impedance path for the peak currents that are to be provided to the load. 3.2 control input (in) the mosfet driver input is a high-impedance, ttl/ cmos-compatible input. the input also has hysteresis between the high and low input levels, allowing them to be driven from slow rising and falling signals, and to provide noise immunity. 3.3 ground (gnd) ground is the device return pin. the ground pin should have a low impedance connection to the bias supply source return. high peak currents will flow out the ground pin when the capacitive load is being discharged. 3.4 output (out) the output is a cmos push-pu ll output that is capable of sourcing and sinking 0.5a of peak current (v dd = 18v). the low output impedance ensures the gate of the external mosfet will stay in the intended state even during large transients. this output also has a reverse current latch-up rating of 0.5a. sot-23-5 symbol description 1 gnd ground 2v dd supply input 3 in control input 4 gnd ground 5 out output note 1: duplicate pins must be connected for proper operation.
mcp1401/02 ds22052a-page 10 ? 2007 microchip technology inc. 4.0 application information 4.1 general information mosfet drivers are high-speed, high current devices which are intended to source/sink high peak currents to charge/discharge the gate capacitance of external mosfets or igbts. in high frequency switching power supplies, the pwm controller may not have the drive capability to directly drive the power mosfet. a mos- fet driver like the mcp1401/02 family can be used to provide additional source/sink current capability. 4.2 mosfet driver timing the ability of a mosfet driver to transition from a fully off state to a fully on state are characterized by the drivers rise time (t r ), fall time (t f ), and propagation delays (t d1 and t d2 ). the mcp1401/02 family of drivers can typically charge and discharge a 470 pf load capacitance in 19 ns along with a typical matched propagation delay of 35 ns. figure 4-1 and figure 4-2 show the test circuit and timing waveform used to verify the mcp1401/02 timing. figure 4-1: inverting driver timing waveform. figure 4-2: non-inverting driver timing waveform. 4.3 decoupling capacitors careful layout and decoupling capacitors are highly recommended when using mosfet drivers. large currents are required to charge and discharge capacitive loads quickly. for example, approximately 550 ma are needed to charge a 470 pf load with 18v in 15 ns. to operate the mosfet driver over a wide frequency range with low supply impedance, a ceramic and low esr film capacitor is recommended to be placed in parallel between the driver v dd and gnd. a 1.0 f low esr film capacitor and a 0.1 f ceramic capacitor placed between pins 2 and 1 should be used. these capacitors should be placed close to the driver to minimized circuit board parasitics and provide a local source for the required current. 4.4 pcb layout considerations proper pcb layout is important in a high current, fast switching circuit to provide proper device operation and robustness of design. pcb trace loop area and inductance should be minimized by the use of ground planes or trace under mosfet gate drive signals, separate analog and power grounds, and local driver decoupling. placing a ground plane beneath the mcp1401/02 will help as a radiated noise shield as well as providing some heat sinking for power dissipated within the device. 0.1 f +5v 10% 90% 10% 90% 10% 90% 18v 1f 0v 0v mcp1401 c l = 470 pf input input output t d1 t f t d2 output t r v dd = 18v ceramic 90% input t d1 t f t d2 output t r 10% 10% 10% +5v 18v 0v 0v 90% 90% 0.1 f 1f mcp1402 c l = 470 pf input output v dd = 18v ceramic
? 2007 microchip technology inc. ds22052a-page 11 mcp1401/02 4.5 power dissipation the total internal power dissipation in a mosfet driver is the summation of three separate power dissipation elements. equation 4-1: 4.5.1 capacitive load dissipation the power dissipation caused by a capacitive load is a direct function of frequency, total capacitive load, and supply voltage. the power lost in the mosfet driver for a complete charging a nd discharging cycle of a mosfet is shown in equation 4-2 . equation 4-2: 4.5.2 quiescent power dissipation the power dissipation associated with the quiescent current draw depends upon the state of the input pin. the mcp1401/02 devices have a quiescent current draw when the input is high of 850 ma (typ) and 100 ma (typ) when the input is low. the quiescent power dissipation is shown in equation 4-3 . equation 4-3: 4.5.3 operating power dissipation the operating power dissipation occurs each time the mosfet driver output transitions because for a very short period of time both mosfets in the output stage are on simultaneously. this cross-conduction current leads to a power dissipation described in equation 4-4 . equation 4-4: p t p l p q p cc ++ = where: p t = total power dissipation p l = load power dissipation p q = quiescent power dissipation p cc = operating power dissipation p l fc t v dd 2 = where: f = switching frequency c t = total load capacitance v dd = mosfet driver supply voltage p q i qh di ql 1 d ? () + () v dd = where: i qh = quiescent current in the high state d = duty cycle i ql = quiescent current in the low state v dd = mosfet driver supply voltage p cc cc f v dd = where: cc = cross-conduction constant (a*sec) f = switching frequency v dd = mosfet driver supply voltage
mcp1401/02 ds22052a-page 12 ? 2007 microchip technology inc. 5.0 packaging information 5.1 package marking information (not to scale) legend: xx...x customer-specific information y year code (last digit of calendar year) yy year code (last 2 digits of calendar year) ww week code (week of january 1 is week ?01?) nnn alphanumeric traceability code pb-free jedec designator for matte tin (sn) * this package is pb-free. the pb-free jedec designator ( ) can be found on the outer packaging for this package. note : in the event the full microchip part nu mber cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. 3 e 3 e 5-lead sot-23 example: 1 standard markings for sot-23 part number code mcp1401t-e/ot gynn mcp1402t-e/ot gznn xxnn 1 gynn
? 2007 microchip technology inc. ds22052a-page 13 mcp1401/02 5-lead plastic small outline transistor (ot) [sot-23] notes: 1. dimensions d and e1 do not include mold flash or protrusions. mold flash or protrusions shall not exceed 0.127 mm per side. 2. dimensioning and tolerancing per asme y14.5m. bsc: basic dimension. theoretically exact value shown without tolerances. note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging units millimeters dimension limits min nom max number of pins n 5 lead pitch e 0.95 bsc outside lead pitch e1 1.90 bsc overall height a 0.90 ? 1.45 molded package thickness a2 0.89 ? 1.30 standoff a1 0.00 ? 0.15 overall width e 2.20 ? 3.20 molded package width e1 1.30 ? 1.80 overall length d 2.70 ? 3.10 foot length l 0.10 ? 0.60 footprint l1 0.35 ? 0.80 foot angle 0 ? 30 lead thickness c 0.08 ? 0.26 lead width b 0.20 ? 0.51 n b e e1 d 1 2 3 e e 1 a a1 a2 c l l1 microchip technology drawing c04-091b
mcp1401/02 ds22052a-page 14 ? 2007 microchip technology inc. notes:
? 2007 microchip technology inc. ds22052a-page 15 mcp1401/02 appendix a: revision history revision a (june 2007) ? original release of this document.
mcp1401/02 ds22052a-page 16 ? 2007 microchip technology inc. notes:
? 2007 microchip technology inc. ds22052a-page 17 mcp1401/02 product identification system to order or obtain information, e.g., on pricing or de livery, refer to the factory or the listed sales office . device: mcp1401: 500 ma mosfet driver, inverting mcp1402: 500 ma mosfet driver, non-inverting tape and reel t = tape and reel temperature range: e = -40c to +125c package: * ot = plastic thin small outline transistor (ot) , 5-lead * all package offerings are pb free (lead free) examples: a) mcp1401t-e/ot: 500 ma inverting mosfet driver, 5ld sot-23 package. a) mcp1402t-e/ot 500 ma non-inverting, mosfet driver, 5ld sot-23 package, part no. x x temperature tape & reel range device xx package range
mcp1401/02 ds22052a-page 18 ? 2007 microchip technology inc. notes:
? 2007 microchip technology inc. ds22052a-page 19 information contained in this publication regarding device applications and the like is prov ided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application me ets with your specifications. microchip makes no representations or warranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip devices in life support and/or safe ty applications is entirely at the buyer?s risk, and the buyer agrees to defend, indemnify and hold harmless microchip from any and all damages, claims, suits, or expenses resulting fr om such use. no licenses are conveyed, implicitly or ot herwise, under any microchip intellectual property rights. trademarks the microchip name and logo, the microchip logo, accuron, dspic, k ee l oq , k ee l oq logo, micro id , mplab, pic, picmicro, picstart, pro mate, rfpic and smartshunt are registered trademarks of microchip technology incorporated in the u.s.a. and other countries. amplab, filterlab, linear active thermistor, migratable memory, mxdev, mxlab, seeval, smartsensor and the embedded control solutions company are registered trademarks of microchip te chnology incorporated in the u.s.a. analog-for-the-digital age, a pplication maestro, codeguard, dspicdem, dspicdem.net, dspicworks, ecan, economonitor, fansense, flexrom, fuzzylab, in-circuit serial programming, icsp, icepic, mindi, miwi, mpasm, mplab certified logo, mplib, mplink, pickit, picdem, picdem.net, piclab, pictail, powercal, powerinfo, powermate, powertool, real ice, rflab, select mode, smart serial, smarttel, total endurance, uni/o, wiperlock and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of mi crochip technology incorporated in the u.s.a. all other trademarks mentioned herein are property of their respective companies. ? 2007, microchip technology incorporated, printed in the u.s.a., all rights reserved. printed on recycled paper. note the following details of the code protection feature on microchip devices: ? microchip products meet the specification cont ained in their particular microchip data sheet. ? microchip believes that its family of products is one of the mo st secure families of its kind on the market today, when used i n the intended manner and under normal conditions. ? there are dishonest and possibly illegal meth ods used to breach the code protection fe ature. all of these methods, to our knowledge, require using the microchip pr oducts in a manner outside the operating specif ications contained in microchip?s data sheets. most likely, the person doing so is engaged in theft of intellectual property. ? microchip is willing to work with the customer who is concerned about the integrity of their code. ? neither microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as ?unbreakable.? code protection is constantly evolving. we at microchip are committed to continuously improving the code protection features of our products. attempts to break microchip?s c ode protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your softwar e or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona; gresham, oregon and design centers in california and india. the company?s quality system processes and procedures are for its pic ? mcus and dspic ? dscs, k ee l oq ? code hopping devices, serial eeproms, microperi pherals, nonvolatile memory and analog products. in addition, microchip?s quality system for the design and manufacture of development systems is iso 9001:2000 certified.
ds22052a-page 20 ? 2007 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://support.microchip.com web address: www.microchip.com atlanta duluth, ga tel: 678-957-9614 fax: 678-957-1455 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit farmington hills, mi tel: 248-538-2250 fax: 248-538-2260 kokomo kokomo, in tel: 765-864-8360 fax: 765-864-8387 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 santa clara santa clara, ca tel: 408-961-6444 fax: 408-961-6445 toronto mississauga, ontario, canada tel: 905-673-0699 fax: 905-673-6509 asia/pacific asia pacific office suites 3707-14, 37th floor tower 6, the gateway harbour city, kowloon hong kong tel: 852-2401-1200 fax: 852-2401-3431 australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8528-2100 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8665-5511 fax: 86-28-8665-7889 china - fuzhou tel: 86-591-8750-3506 fax: 86-591-8750-3521 china - hong kong sar tel: 852-2401-1200 fax: 852-2401-3431 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8203-2660 fax: 86-755-8203-1760 china - shunde tel: 86-757-2839-5507 fax: 86-757-2839-5571 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7252 fax: 86-29-8833-7256 asia/pacific india - bangalore tel: 91-80-4182-8400 fax: 91-80-4182-8422 india - new delhi tel: 91-11-4160-8631 fax: 91-11-4160-8632 india - pune tel: 91-20-2566-1512 fax: 91-20-2566-1513 japan - yokohama tel: 81-45-471- 6166 fax: 81-45-471-6122 korea - daegu tel: 82-53-744-4301 fax: 82-53-744-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - penang tel: 60-4-646-8870 fax: 60-4-646-5086 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-572-9526 fax: 886-3-572-6459 taiwan - kaohsiung tel: 886-7-536-4818 fax: 886-7-536-4803 taiwan - taipei tel: 886-2-2500-6610 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-39 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 uk - wokingham tel: 44-118-921-5869 fax: 44-118-921-5820 w orldwide s ales and s ervice 06/25/07

▲Up To Search▲

Price & Availability of MCP1402T-EOT

	To Download MCP1402T-EOT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .